proprietary and confidential property of superworld (a) (c) (b) (e) (d) 1. part no. expression : (b) dimension code (c) material code (a) series code 2. conf igurat ion & di me ns ions : 4. mate ri als : superworld electronics (s) pte ltd 3. sche mati c : (e) r : tape & reel (f) rated current : b = 200ma pg. 1 pcb pattern 2.8 0.2 1.0 0.1 3.2 0.2 5.2 3.6 0.85 0.7 1.2 0.1 b c d1 d2 l h k1 k2 waq 7 f 5 1 0 - r b - 1 0 2 a b d2 1 43 l h g1 4 1 3 2 4.5 0.2 a 3 g1 (f) (g) (d) inductance code : 510 = 51 uh (g) 10 : internal control number (b) core:ferrite core d (c) termination : tin (pb free) (d) wire : enameled copper wire c b (a) upper plate:ferrite a pc board should be designed so that products are not sufficient products shall be positioned in the sideway direction against the mechanical stress to prevent failure. under mechanical stress as warping the board. wirewound type common mode filter (rohs compliant) approved engineering controlled copy c d1 k2 k1 g2 unit:m/m 0.9 g2 k2 k1 d1 d2 01.04.2015 note : specifications subject to change without notice. please check our website for latest information. waq7f series 01 apr 2015
superworld electronics (s) pte ltd 6. electrical characteristics : a) test frequency inductance:100khz/0.1v; impedance:10mhz/0.1v pg. 2 5. ge ne ral sp ecif ication : ( ? ) WAQ7F510-RB-10 part no. ( ? ) max. 51+50/-30% ( uh ) inductance common mode 1.0 dcr 50 ( vdc ) voltage rated 200 ( ma ) current rated 10m ir min. 7. characteristics curves : wirewound type common mode filter (rohs compliant) approved engineering controlled copy proprietary and confidential property of superworld c) storage temperature:-40 ~ +125 b) operating temperature: -40 ~ +125 d) all test data is referenced to 25 ambient. 1 10 100 1000 f req uency(mhz) 1 10 100 1000 10000 10000 0 impedance(ohm) common mode normal mode e) indicate compliant to aec-q200 and ppap level4 eligibility WAQ7F510-RB-10 waq7f101-ra-10 100+50/-30% 2.0 50 100 10m waq7f110-rb-10 11+50/-30% 0.8 50 200 10m waq7f110-rb-10 waq7f101-ra-10 note : specifications subject to change without notice. please check our website for latest information. waq7f series 1101001000 frequency(mhz) 1 10 10 0 1000 10 00 0 impedance(ohm) a cm 45 32 f2 s f -1 1 0 common mode norma l m ode 110100100 0 fre quency(mhz) 10 100 1000 10000 10000 0 im ped an ce(ohm ) commo n m ode normal mode 01.04.2015 01 apr 2015
proprietary and confidential property of superworld 8. re li abil it y & te st condition : termi nal s trength solder heat resistance solderability test mechanical performance test temperature rise test z (c ommon mode) electrical characteristics test item i.r. dcr test condition performance a gi l ent4339 2. temperature measured by digital surface thermometer. refer to standard electrical characteristics list more than 90% of termincal electr ode should be covered with solder. rated current < 1a t 20cmax 1. applied the allowed dc current. agilent-4291a+ agilent - 16197a a gi l ent-4338b rated current 1a t 40cmax R rdc w i thi n 15% of i ni ti al value and shall not appearance n o damage. inductance within10% of initial value exceed the specification value s ol der tamperature: 260 5 c temperature ramp/i mmers i on and immersion d i p ti me: 10 1sec. depth: completely cover the termination. rate: 25 6 mm/s ( ipc/jedec j-std-020d classification reflow profiles) with the component mounted on a pcb with the device to be tested, apply a force (>0805:1kg , <= 0805:0.5kg)to preconditioning : run through ir reflow for 2 times. the side of a device being tested. this force shall be applied for 60 +1 seconds. also the force shall be applied gradually as not to apply a shock to the com ponent being tested. superworld electronics (s) pte ltd flux for lead free: rosin. 9.5% d i p ti me: 41sec depth: completely cover the termination wirewound type common mode filter (rohs compliant) approved engineering controlled copy preheat: 150 ,60sec. solder: sn99.5%-cu0. 5% temperature: 2455 number of heat cycles:1 note : specifications subject to change without notice. please check our website for latest information. pg. 3 waq7f series 01.04.2015 01 apr 2015
proprietary and confidential property of superworld pg. 4 humidity resistance test thermal shock life test reliabilty test item humidity : 85 2% r.h measured at room temperature after placing for 24 2 hrs duration 1000hrs min. with 100% rated current number of cycles 500 temperature : 85 2 c measured at room fempraturc after placing for 24 2 hrs step 1 3 2 30 5 -40 2 25 2 105 2 0.5 Q 30 5 temperature ( c) times (min.) performance test condition testing time : 12 hours(20 minutes, 12 cycles each of 3 orientations) total amplitude : 1.52mm 10% oscillation fr equency : 10 2k 10hz for 20 minutes vibration test equipment : vibration checker 8. re li abil it y & te st condition : duration : 1000 12hrs applied current : rated current temperature : 85 2 c measured at room temperature after placing for 24 2 hrs. ( ipc/jedec j-std-020d classification reflow profiles) preconditioning: run through ir reflow for 2 times. ( ipc/jedec j-std-020d classification reflow profiles) preconditioning: run through ir reflow for 2 times. ( ipc/jedec j-std-020d classification reflow profiles) preconditioning: run through ir reflow for 2 times. ( ipc/jedec j-std-020d classification reflow profiles) preconditioning: run through ir reflow for 2 times. superworld electronics (s) pte ltd wirewound type common mode filter (rohs compliant) approved engineering controlled copy rdc w i thi n 15% of i ni ti al value and shall not appearance n o damage. inductance within10% of initial value exceed the specification value note : specifications subject to change without notice. please check our website for latest information. waq7f series 01.04.2015 01 apr 2015
proprietary and confidential property of superworld b) 355 c tip temperature (max) e) use a 20 watt soldering iron with tip diameter of 1.0mm f) limit soldering time to 4-5 secs. d) 1.0mm tip diameter (max) c) never contact the ceramic with the iron tip if hand soldering cannot be avoided, the preferred technique is the utilization of hot air soldering tools. mildly activated rosin fluxes are preferred. our terminations are suitable for all wave and re-flow soldering systems. recommended temperature profiles for re-flow soldering in figure 1. products attachment with soldering iron is discouraged due to the inherent process control limitations. in the event that a soldering iron must be employed the following precautions are recommended. 9-1.1 solder re-flow : a) preheat circuit and products to 150 c. 9-1.2 soldering iron (figure 2) : note : 9. soldering and mounti ng : 9-1. soldering soldering tp(260 c/10s max) 60~150s time(sec.) reflow times: 3 times max. temperature c 150 60~180s 4 80s max. 25 tp(2 45 c/2 0~4 0s) 200 217 preheating o ve r 60s. g rad ual cooling within 4-5s iron soldering times: 1 times max. temperature c cooling natural cooling 350 150 soldering preheating natural fig.2 fig.1 time(sec.) superworld electronics (s) pte ltd wirewound type common mode filter (rohs compliant) approved engineering controlled copy pg. 5 note : specifications subject to change without notice. please check our website for latest information. waq7f series 01.04.2015 01 apr 2015
proprietary and confidential property of superworld superworld electronics (s) pte ltd pg. 6 ko(mm) 3.00 0.1 bo(mm) 4.90 0.1 ao(mm) 3.60 0.1 p(mm) 8.0 0.1 t(mm) 0.26 0.05 d(mm) 178.0 2.0 10-2 tape dimension / 12mm 7" x 8mm d c b r0.5 r1.9 1 2 0 x 7" x 12mm 2 0.5 60.0 2.0 r10.5 13.5 0.5 7" x 12mm 13.5 0.5 13.5 0.5 type a(mm) c(mm) b(mm) 10-1. reel dimension 10. packaging information : a 10-3. packing quantity carton middle box chip / reel series inner box 25000 12500 500 2500 waq7f wirewound type common mode filter (rohs compliant) approved engineering controlled copy p 5.5 0.05 d1:1.5 0.1 1.75 0.1 po:4 0.1 d:1.5+0.1 bo w:12.0 0.1 ko ao p2:2 0.05 t section a-a a a series waq7f note : specifications subject to change without notice. please check our website for latest information. waq7f series 01.04.2015 01 apr 2015
superworld electronics (s) pte ltd pg. 7 10-4. tearing off force base tape a) temperature and humidity conditions : less than 40 c and 60% rh. b) recommended products should be used within 12 months from the time of delivery. c) the packaging material should be kept where no chlorine or sulfur exists in the air. b) the use of tweezers or vacuum pick up is strongly recommended for individual components. c) bulk handling should ensure that abrasion and mechanical shock are minimized. a) products should be handled with care to avoid damage or contamination from perspiration and skin oils. to maintain the solderabililty of terminal electrodes : 1. storage conditions : application notice 2. transportation : top cover tape 165 to 180 f teari ng speed in the arrow direction under the following conditions. the force for tearing off cover tape is 15 to 80 grams 45~85 5~35 860~1060 room humidity ( c) room temp. (%) (hpa) room atm 300 (mm/min) wirewound type common mode filter (rohs compliant) approved engineering controlled copy proprietary and confidential property of superworld note : specifications subject to change without notice. please check our website for latest information. waq7f series 01.04.2015 01 apr 2015
|
